|
TEMTRO™
Dry Gel
=================================================================
Section
I - Product Identification
=================================================================
Identity:
TEMTRO™ Dry Gel
Manufacturer's Name:
Roshgo Corporation
Address:
P.O. Box 2052, Alpharetta, GA 30023
Emergency Telephone Number:
Chemtrec (24 hours) 1-800-424-9300
Telephone Number for
Information:
678-867-0461
Date Prepared:
November 15, 2001
==================================================================
Section
II - Composition/Information on ingredients
==================================================================
Superabsorbent Crosslinked
Sodium Polymer
OSHA PEL:
NE
ACGIH TLV:
NE
Other Limits Recommended:
Recommended inhalation exposure limit guideline is 0.05
mg/m3
==================================================================
Section III - Physical/Chemical
Characteristics
==================================================================
Boiling Point:
NE
Vapor pressure (mm
Hg.): Less than 10
Vapor Density (AIR=1):
NE
Solubility in Water:
Insoluble
Appearance and Odor:
White granular powder with no odor
Specific Gravity (H2O=1):
Bulk Density: 0.4-0.7
Melting Point:
> 3900F
Evaporation Rate (Butyl
Acetate=1): < 1
===================================================================
Section IV -
Fire and Explosion Hazard Data
===================================================================
Flash Point (Method
Used): None
Flammable Limits:
NE
Extinguishing Media:
Water, CO2, and dry chemical extinguishants
Special Fire Fighting
Procedures:
None
Unusual Fire and Explosion
Hazards:
Water based. Difficult to ignite unless directly involved
in flame. Extremely slippery conditions are created if
spilled and comes into contact with water
===================================================================
Section V - Reactivity Data
===================================================================
Stability:
Stable
Incompatibility (Materials
to Avoid): Strong Oxidizers
Hazardous Decomposition or
Byproducts:
Thermal Decomposition: CO,
CO2,
Hydrocarbons, oxides of carbon and nitrogen. DO NOT
breathe
fumes
or smoke.
Hazardous Polymerization:
May Not Occur
Conditions to Avoid:
None Known
===================================================================
Section VI - Health Hazard Data
===================================================================
Router(s) of Entry:
Inhalation?
Yes
Skin?
No
Ingestion?
No
Health Hazards:
Acute
(short term) inhalation of dust may cause mild irritation
of upper respiratory tract (nose and throat) and lungs
Chronic(long
term) inhalation exposure to rats for a lifetime (2 years)
using the superabsorbent crosslinked polymer that had been
micronized to a respirable particle size (less than 10
microns) produces non specific inflammation and chronic
lung injury at 0.2 mg/m3 and 0.8 mg/m3
At
0.8 mg/m3 tumors were seen in some animals. In
the absence of chronic inflammation, tumors are NOT
expected. There were NO adverse effects of any kind at
0.05 mg/m3
No
effects in mutagenicity tests
Carcinogenicity:
NTP?
No
IARC Monographs?
No
OSHA Regulated?
No
Signs and Symptoms of
Exposure:
Possible
reddening, drying of skin or eyes with itching, burning or
other discomfort; irritation of nose and throat
Medical Conditions Generally
Aggravated by Exposure:
May
aggravate existing respiratory conditions; skin conditions
(due to drying effect)
Emergency and First Aid
Procedures:
Ingestion:
Drink
copious amounts of water and consult physician.
Inhalation:
Remove
to source of fresh air.
Eyes:
Flush
with water and consult physician.
Skin:
Wash
with soap and water.
Call
a physician regarding any continued discomfort
===================================================================
Section
VII - Precautions for Safe Handling and Use
===================================================================
Steps to be taken in case
material is released or spilled:
Avoid
contact with water. Product is extremely slippery when
contacted with water. Protective shoes may be worn and
product may be shoveled up and placed in container for
disposal.
Waste Disposal Method:
Dispose
of in accordance with all local, state, and federal
regulations. Non-hazardous material waste material
suitable for approved solid waste landfill.
Precautions to be Taken in
Handling and Storage:
Handle
as eye irritant. Do not get into eyes. Avoid prolonged or
repeated skin contact. Do not inhale dust. Do not digest.
Other Precautions:
Dusty
conditions may irritate the eyes and respiratory system.
Wear goggles and mask with high efficiency filter where
dust is created.
===================================================================
Section VIII - Control Measures
===================================================================
Respiratory Protection(Specify
Type): Wear respirator or mask with high efficiency filter
for particulate levels above 0.05 mg/m3
Ventilation:
Local exhaust to ensure airborne particulates are removed.
Mechanical ventilation recommended.
Eye Protection:
Safety glasses or goggles.
Protective Gloves:
Impervious rubber.
Other Protective Clothing or
Equipment:
None
Work/Hygienic Practices:
Use good housekeeping practices. Wash thoroughly after
handling.
-----------------------------------------
ABBREVIATIONS:
NA=
Not Applicable; NH= Non Hazardous; NE=Not Established
The
information contained herein has been compiled from
sources believed to be reliable and is accurate to the
best of our knowledge. However, Roshgo Corporation cannot give any
guarantees regarding information from other sources, and
expressly does not make any warranties, nor assumes any
liability for its use.
|
